What Does Ice Maker Repair Cost?
Ice maker repair costs $100 to $225, averaging around $160. A diagnostic or service call runs $75 to $150 and is often credited toward the repair. Minor repairs to the water valve, fill tube, feeler arm, or sensors run $100 to $160. Replacing the control module or the full ice maker assembly runs $160 to $225. Here is how each tier breaks down.
Diagnostic or Service Call: $75 to $150
Most appliance technicians charge $75 to $150 to visit and diagnose the problem. The fee covers travel and diagnostic time and is separate from parts and labor, though most companies credit it toward the repair if you proceed. Confirm the policy when you book.
Common Minor Repairs: $100 to $160
The water inlet valve, a solenoid valve that opens to fill the ice maker tray, is the most commonly replaced ice maker component. It fails by clogging, by sticking open so the unit overfills, or by sticking closed so no ice is produced. The part costs $40 to $80 plus labor. (For more on this, see What Causes Ice Maker Problems?.)
The fill tube can freeze over and block water delivery; clearing or replacing it runs $100 to $150 including labor. The feeler arm, which stops production when the bin is full, can stick in the up position and pause the ice maker indefinitely — usually a $50 to $100 fix. With labor, repairs at this tier land at $100 to $160 all-in.
Ice Maker Assembly Replacement: $160 to $225
On built-in refrigerator ice makers, individual component repair is often impractical, so the whole module is swapped as a unit. Assembly kits cost $60 to $150 in parts and are plug-and-play on most major brands, bringing the installed total to $160 to $225. On an older ice maker this is frequently more efficient than diagnosing and replacing components one at a time. (For more on this, see What Affects the Cost of Ice Maker Repair?.)
Check the Filter and the Water Supply First
Before calling anyone, replace the refrigerator’s water filter. A clogged filter drops water pressure at the ice maker below what the fill valve needs to open properly, which produces slow ice, small cubes, or no ice at all. A new filter costs $15 to $50 and resolves a meaningful share of ice maker complaints without a service call.
Water pressure is worth checking at the same time. Most refrigerator ice makers need a minimum of 20 PSI at the inlet valve to fill correctly; below that the valve may not open, or may open only partway. Look at the saddle valve on the supply line behind the refrigerator too, since a partially closed or clogged saddle valve is a common cause of low pressure to the ice maker.
Ice Maker Repair Cost at a Glance
| Item | Cost |
|---|---|
| Replacement water filter | $15 to $50 |
| Diagnostic or service call | $75 to $150, typically credited |
| Water inlet valve, parts | $40 to $80 |
| Ice maker arm repair | $50 to $100 |
| Fill tube clearing or replacement | $100 to $150 |
| Minor repair, parts and labor | $100 to $160 |
| Assembly kit, parts | $60 to $150 |
| Full assembly replacement, installed | $160 to $225 |
| Overall range | $100 to $225, averaging $160 |
Cost figures on this page were checked against published pricing on August 22, 2026. How we source cost data.
Why Ice Makers Stop Working
The usual suspects, in the order a technician rules them out: a clogged water filter, a frozen fill tube blocking water delivery, a failed water inlet valve, a feeler arm stuck in the off position, a failed ice maker control module, or low water pressure from the supply line. The diagnosis follows the sequence of operation — whether the unit receives water at all, whether it attempts to cycle, and whether it ejects ice.
Cost within each tier also moves with which component failed, whether the part is in stock or must be ordered, the brand and model, local labor rates, and how much disassembly the job requires. Parts for premium or less common brands cost more and take longer to source than parts for widely sold brands.
Some of this is DIY territory. A whole-assembly swap is the most approachable job on the list, since the module disconnects from the water line and wiring harness and the replacement plugs straight in on most major brands — the main risk is ordering the wrong assembly, so confirm the exact part number for your model before buying. Individual component work such as the water inlet valve or the control board is also DIY-accessible, but it takes more diagnostic skill to be sure you are replacing the part that actually failed.
Repair, Replace, and Reading the Quote
At $100 to $225, ice maker repair is almost always worth it on a refrigerator that is otherwise in good shape: you are preserving the function of an $800 to $1,500 appliance for a fraction of its value. The exception is a refrigerator over 12 years old that is showing other failures as well, where the money is better put toward replacing the whole unit. The general appliance test still applies — if a repair exceeds half of replacement cost on a unit more than five or six years old, get a replacement quote alongside the repair quote. (For more on this, see How Long Does Ice Maker Repair Take?.)
A repair quote should name the failed component, list parts and labor separately, and state whether the part is in stock or has to be ordered. A total with no itemization does not give you enough to decide on. When comparing quotes from multiple companies, confirm each covers the same diagnosed component, the same parts situation, and the same labor guarantee; a quote well below the others usually reflects a different diagnosis or thinner scope rather than better pricing. The diagnostic fee is worth paying even if you end up replacing the appliance, because knowing what failed and why informs that decision.
Frequently Asked Questions
Ice maker repair runs $100 to $225, averaging $160. The diagnostic call is $50 to $125, minor repairs to the water valve, fill tube, or arm run $100 to $160, and full assembly replacement runs $160 to $225. Replace the water filter, at $15 to $50, before calling a technician.
Yes. The $50 to $125 diagnostic fee is charged whether or not you proceed, and most companies credit it toward the repair if you do. Confirm the policy when booking.
Most often a clogged water filter, a frozen fill tube blocking water delivery, a failed water inlet valve, a feeler arm stuck in the off position, a failed control module, or low water pressure from the supply line. A technician narrows it down by whether the unit receives water, attempts to cycle, and ejects ice.
Almost always, at $100 to $225 on a refrigerator in otherwise good condition -- the repair preserves the function of an $800 to $1,500 appliance. Skip it only when the refrigerator is over 12 years old and other components are failing too, in which case put the money toward replacing the unit.
Yes for whole-assembly replacement. Ice maker assemblies on most major brands are plug-and-play modules: disconnect the water line and wiring harness, install the new assembly, reconnect. Kits cost $60 to $150. The main risk is ordering the wrong assembly, so confirm the exact part number for your model first.
Yes. Most refrigerator ice makers require at least 20 PSI at the inlet valve to fill correctly. Below that the valve may not open or may open only partially, producing small cubes or no ice. Check the home's water pressure and the saddle valve on the supply line behind the refrigerator, which is a common source of restriction.
Control module failure and full assembly replacement, at $160 to $225 installed. On built-in ice makers the whole module is usually swapped rather than repaired piece by piece, which is often the more efficient route on an older unit anyway.
Yes. Parts for premium or less common brands cost more and take longer to source than parts for widely sold mainstream brands, so those repairs run higher and take longer to schedule. Parts availability is worth asking about when you get the quote.